Tuesday, July 5, 2011

Pantie liner



OK, so here's something a bit different. I know this isn't for everyone but If I am seeking something like this I can't be that unique that nobody else would also like it.

I'm all about natural stuff and I have been using a menstrual cup for over 5 years now. the thing is I still use pantie liners and have been toying for a while about a way to make my own. I did have some flannel ones but they would scrunch up in uncomfortable ways. I recently tried one in seed stitch and it was just to thin and flimsy.

this is the design I settled on. it's a 1x1 rib so thicker and more stable. I like mine a bit wide. This is rather the formula I used to create one so adjust as you desire. for a general guideline I took one of my liners of my fave brand and used that as a visual adjusting size as I saw fit.

This is not designed to replace a pad as it's not thick enough for such use. But it is a nice substitute for a every day pantie liner.


needle: us 5
yarn: Hobby Lobby's "I Love This Cotton!" This is a VERY soft 100% cotton and feels nice against the skin. I t is a sport type weight.

I like to slip one stitch on my edges, It helps to keep things looking neat.

I suggest making 1 and using it and washing it to see where you may want to customize this more to your liking. Also I suggest making it just a tad wider than what you think is good. they do compress a bit when you wear them.

for the increases just either make one knit or make one purl. I prefer to do this at the end of the row but I like to set it up with a YO at the beginning of the row which makes it easier to twist the stitch when you do your m1. Being a 1x1 rib if you want to set up with a YO you will have to do either a yo front or yo bak depending on weather you have a knit stitch or a purl stitch following the yo.

For mine I cast on 15 stitches.

(always knit the 1st stitch).
row 1: k1, p1 to last stitch, slip last stitch with yarn in front
row 2: k1, yo, work the k1, p1 rib to last stitch and slip last stitch wyif
row 3: k1, yo, work rib to yo, use the yo to either make one knit or make one purl by twisting the yo as you stitch into it, slip last stitch wyif.

repeat row 3 till it is of the desired width. (I increased till I had 21 stitches.)

work a few rows in the k1, p1 rib till top is desired length and you feel it's time to start to reduce. (I worked 7 rows before reducing)

To reduce: k1, work ribbing to last 3 stitches. either k2tog or p2 tog on next 2 stitches, slip last stitch wyif

Repeat reducing row until narrow enough to fit. (I reduced to 10 stitches)

Work k1, p1 rib till the center is of desired length (I worked this for about 10 rows)

Work increasing row 3 for a few rows till bottom is of desired width (I increased to 13 stitches)

work 1x1 rib for a couple rows (I worked for 3 rows).

Reduce again following same formula in row 3 till you have about 6 stitches. bind off.

Of course customize this shape for best fit and comfort.

In short: cast on about 15 stitches, increase till top is desired width, knit till top is desired length, reduce till narrow enough to fit, knit till desired length. increase a little for the bottom and decrease and bind off.

2 comments:

Anonymous said...

What a new idea! You should post it on revelry. I'm sure some other women would be interested in finding this pattern. I'm new toying blog - check mind out and follow me too if you're interested. :)

GsCraftsNthings said...

Thanks! I am on Rav and there I'm GsCraftsNthing http://www.ravelry.com/people/GsCraftsNthings and I have been putting patterns up there which link back to my blog.